Difference between revisions of "Dev:cc3200"
(→Resources) |
|||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{TocRight}} |
|||
TI Chip with Arm Cortex M4 and network processor with ipV4 in hardware. |
TI Chip with Arm Cortex M4 and network processor with ipV4 in hardware. |
||
| ⚫ | |||
| ⚫ | |||
= Code Composer studio on Linux = |
|||
| ⚫ | |||
* [http://processors.wiki.ti.com/index.php/Linux_Host_Support_CCSv6 TI CCS v6 wiki] |
|||
* During install complains about libudev.so.0 missing. Then do: |
|||
sudo ln -s /lib/i386-linux-gnu/libudev.so.1 /lib/libudev.so.0 |
|||
| ⚫ | |||
== Serial connection == |
|||
Enable recognition for the serial USB connection, which is a FTDI chip with TI codes: |
Enable recognition for the serial USB connection, which is a FTDI chip with TI codes: |
||
sudo su |
sudo su |
||
| Line 13: | Line 20: | ||
Alternative: use this udev rule: |
Alternative: use this udev rule: |
||
ATTRS{idVendor}=="0451", ATTRS{idProduct}=="c32a", MODE="0660", GROUP="dialout", RUN+="/sbin/modprobe ftdi-sio", RUN+="/bin/sh -c '/bin/echo 0451 c32a > /sys/bus/usb-serial/drivers/ftdi_sio/new_id'" |
ATTRS{idVendor}=="0451", ATTRS{idProduct}=="c32a", MODE="0660", GROUP="dialout", RUN+="/sbin/modprobe ftdi-sio", RUN+="/bin/sh -c '/bin/echo 0451 c32a > /sys/bus/usb-serial/drivers/ftdi_sio/new_id'" |
||
== Tools == |
|||
Install arm tools. May have to remove gdb first. |
|||
sudo apt-get remove gdb |
|||
sudo apt-get install binutils-arm-none-eabi gdb-arm-none-eabi gcc-arm-none-eabi libnewlib-arm-none-eabi |
|||
sudo apt-get install openocd |
|||
| ⚫ | |||
From TI |
|||
* [http://processors.wiki.ti.com/index.php/CC31xx_&_CC32xx cc31xx & cc32xx wiki] |
|||
* [http://www.ti.com/ww/en/launchpad/launchpads-connected-cc3200-launchxl.html cc3200 LaunchPad] |
|||
Other sources: |
|||
| ⚫ | |||
Latest revision as of 17:43, 10 December 2014
TI Chip with Arm Cortex M4 and network processor with ipV4 in hardware.
Code Composer studio on Linux
- During install complains about libudev.so.0 missing. Then do:
sudo ln -s /lib/i386-linux-gnu/libudev.so.1 /lib/libudev.so.0
Notes for Linux
Serial connection
Enable recognition for the serial USB connection, which is a FTDI chip with TI codes:
sudo su modprobe ftdi-sio echo 0451 c32a > /sys/bus/usb-serial/drivers/ftdi_sio/new_id
Alternative: use this udev rule:
ATTRS{idVendor}=="0451", ATTRS{idProduct}=="c32a", MODE="0660", GROUP="dialout", RUN+="/sbin/modprobe ftdi-sio", RUN+="/bin/sh -c '/bin/echo 0451 c32a > /sys/bus/usb-serial/drivers/ftdi_sio/new_id'"
Tools
Install arm tools. May have to remove gdb first.
sudo apt-get remove gdb sudo apt-get install binutils-arm-none-eabi gdb-arm-none-eabi gcc-arm-none-eabi libnewlib-arm-none-eabi sudo apt-get install openocd
Resources
From TI
Other sources:
